news

Thionocarbamate Collector: Dialkyl Chemistry for Selective Copper Flotation

Thionocarbamates occupy a narrow but valuable band in the collector spectrum: stronger than a dithiophosphate, more selective than a xanthate, and effective at low doses. For copper circuits separating chalcopyrite from pyrite, or copper from molybdenum, a thionocarbamate collector is often the difference between a saleable concentrate and a penalty-laden one. This guide covers the chemistry of the family, how the main grades differ, where they outperform xanthates, and what to specify when sourcing.

What a Thionocarbamate Collector Actually Is

A thionocarbamate is an O-alkyl N-alkyl thiocarbamate, written structurally as R-O-C(=S)-NH-R’. The molecule combines an alkoxy group, a thiocarbonyl sulfur and an amine nitrogen in one compact framework. That arrangement produces two useful properties at once: the thiocarbonyl sulfur coordinates strongly with copper and other chalcophile metals, while the nitrogen-side substituent can be tuned to adjust hydrophobicity and steric bulk.

The practical consequence is a collector that chemisorbs on copper sulfides through a bidentate-like interaction, forming a stable surface complex without the strong frothing tendency and high reactivity that make xanthates difficult to control in cleaner circuits. Thionocarbamates are typically supplied as oily liquids, insoluble in water but soluble in the reagents used to prepare plant solutions, and are usually added as emulsions or in a light oil carrier.

The Main Grades: IPETC, Z-200 and Allyl Variants

Suppliers describe thionocarbamates by their alkyl groups, and three types dominate commercial use.

Copper flotation bank with mineral-rich froth overflowing the cell lip
  • Isopropyl ethyl thionocarbamate (IPETC, commonly sold as Z-200) is the reference grade. It is the most widely used member of the family. Its balance of selectivity and collecting strength makes it a default choice for chalcopyrite flotation where pyrite rejection matters.
  • Allyl isopropyl thionocarbamate carries an unsaturated allyl group that raises collecting power. It suits ores where copper minerals are finely disseminated or partially oxidized, at some cost in selectivity.
  • Ethyl and methyl variants are shorter-chain grades used where a lighter touch is required, for example in cleaner stages or in circuits already carrying a strong primary collector.

Grade selection is rarely about which is “best.” It is about matching chain length and unsaturation to liberation size, pyrite content and the depression regime in use. A plant running a high-pyrite ore will usually prefer IPETC; a plant fighting poor recovery on a partially oxidized copper ore may gain more from an allyl grade.

Why Thionocarbamates Beat Xanthates in Some Circuits

Xanthates are cheap, powerful and forgiving, which is why they remain the default rougher collector worldwide. Their weakness is selectivity: a xanthate will happily collect pyrite, and at the doses needed for good copper recovery it can drag iron sulfide into the concentrate.

Thionocarbamates trade some raw collecting power for a cleaner surface chemistry. In practice this shows up as:

  • Better copper-iron separation at equivalent copper recovery, reducing the need for high lime additions or strong depressants.
  • Lower dosage, often 10–30 g/t in cleaner and scavenger applications versus substantially higher xanthate rates.
  • Weaker frothing, which can simplify froth control in circuits where xanthate over-frothing has been a problem.
  • Improved performance in mildly alkaline pulps, where some dithiophosphates lose efficiency.

The trade-off is cost per kilogram and a narrower window of optimal pH. Thionocarbamates perform best around pH 8–10 and lose selectivity if the circuit swings strongly alkaline.

If you are still mapping collector families against ore types, the site’s guide to xanthate collectors covers the baseline every flotation engineer works from.

Where Thionocarbamates Earn Their Cost

Three circuit types account for most thionocarbamate consumption.

Copper roughing and cleaning on high-pyrite ores. Here the collector’s selectivity reduces the mass pull to cleaner and lowers smelter penalties. Many operations run a xanthate in the rougher and a thionocarbamate in the cleaner, letting each reagent do what it does best.

Copper-molybdenum separation. Thionocarbamates are used to float copper away from molybdenite or, in reverse circuits, to assist molybdenum flotation where copper has been depressed. The low dosage and clean kinetics suit the small tonnages and tight control of a Cu-Mo plant.

Copper-zinc and copper-lead circuits. Selective copper flotation ahead of zinc or lead requires a collector that will not activate or collect the sulfide being depressed. Thionocarbamates fit this role well, particularly where zinc sulfate or cyanide is used as a depressant.

The site’s page on isopropyl ethyl thionocarbamate Z-200 sets out the reference grade’s properties in detail.

Dosage, pH and Circuit Practice

Typical thionocarbamate additions fall in the 5–50 g/t range, with cleaners and Cu-Mo circuits at the low end and roughers on difficult ores at the high end. Because the reagent is oily, it must be emulsified before addition — either with a small quantity of emulsifier and water, or by metering into the ball mill feed where mechanical dispersion does the work.

Three practical points matter. First, stage the addition: adding all the reagent to the rougher usually wastes it, whereas splitting between rougher and scavenger improves recovery per kilogram. Second, watch pH: above roughly pH 11 the reagent’s advantage over xanthate narrows, and lime consumption should be reviewed if selectivity falls away. Third, check froth behaviour: because thionocarbamates froth less than xanthates, the frother dose may need a small increase to maintain froth depth and carrying capacity.

Handling, Packaging and Shipping

Thionocarbamates are supplied in 200 L drums, 1000 L IBCs or ISO tanks. They are combustible liquids with a characteristic sulfurous odour and should be stored away from oxidizers, in a cool, ventilated area with the drums closed. Prolonged exposure to air and light causes darkening and gradual loss of assay, so stock rotation matters.

For export, the reagent normally ships under a combustible liquid classification rather than as a dangerous good, but the exact status depends on flash point and packaging. Confirm the UN number and documentation against the supplier’s safety data sheet.

Specifying and Qualifying a Supplier

A thionocarbamate specification should pin down the following:

  • Assay, expressed as mass fraction of the active thionocarbamate, with the analytical method named.
  • Isomer and alkyl distribution, since a blended grade will not reproduce the flotation response of a pure one.
  • Moisture and acidity, both of which affect storage stability and reagent consumption.
  • Specific gravity and flash point, needed for dosing calibration and transport classification.
  • Appearance, useful as a fast incoming-goods check against a retained reference sample.
  • Batch number and production date with a certificate of analysis per lot.

Beyond paperwork, ask two questions that separate manufacturers from traders: where the reagent is synthesized, and what the batch-to-batch assay tolerance actually is. Then trial the material against your current collector at the same dosage, holding the frother and depressant scheme constant, and compare copper recovery, concentrate grade and the iron content of the concentrate over a full shift.

Conclusion

Thionocarbamates are the precision instrument of sulphide flotation: lower dosage, better selectivity and cleaner concentrates than a xanthate can deliver, at the cost of price and a narrower operating window. IPETC remains the reference grade, allyl variants extend the family where recovery needs help, and the circuit — not the catalogue — decides which one is right. Specify the assay and alkyl distribution precisely, trial before committing, and treat the collector as one lever among several rather than a standalone fix.

Leave a Reply