Sulfurized isobutylene is the workhorse extreme-pressure additive behind most gear oils, metalworking fluids and greases carrying a GL-5 or high-load claim. It is also one of the easiest additives to buy badly. Two drums labelled T321 can differ by ten points of sulfur, by chlorine content, and by how much of that sulfur actually reacts in a four-ball test. This guide sets out what to specify, what to measure, and how to qualify a supplier before a drum reaches your blending line.
Why Sulfurized Isobutylene Dominates EP Formulations
Sulfur-bearing EP additives react with the metal surface under the flash temperatures generated at asperity contacts. The reaction film — iron sulfide and related species — is softer than the base metal but far harder to shear through, which is why it prevents the welding and scuffing a hydrodynamic film cannot survive.
Isobutylene suits this chemistry because its chain is saturated apart from the sulfur bridges, giving better thermal and oxidative stability than the older sulfurized fatty oils while staying soluble in mineral and PAO stocks. The result is a compact additive: 1 to 4 percent of a 40 percent sulfur product can lift a gear oil from a failing FZG stage to a pass at stage 12, with little effect on viscosity or deposits.
What T321 Actually Contains
T321 is the common Chinese industry designation for sulfurized isobutylene. It is not a single specification, and buyers who treat it as one are the buyers who get surprised. Three numbers matter:
Total sulfur typically falls between 40 and 45 percent for the standard grade, with high-sulfur variants in the mid-40s. It is the headline figure on most quotations and the least informative one on its own.
Active sulfur is the fraction that reacts with a copper strip under the standard corrosion test. It delivers EP performance and also attacks yellow metals and some elastomers. A product can be high in total sulfur yet low in active sulfur if the manufacturing route leaves more of the sulfur in stable, non-reactive forms.
Chlorine should be low. Some older sulfurized products carry chlorine from the chlorination step, and chlorine is increasingly restricted under European formulator requirements and OEM specifications.
The gap between total and active sulfur is where most specification disputes originate. Write both into your purchase specification, with test methods named, rather than accepting a single “sulfur content” line.

Grades and What Buyers Compare
| Parameter | Standard T321 | High-sulfur grade | What it means in practice |
|—|—|—|—|
| Total sulfur | 40–42% | 43–46% | Higher sulfur allows lower treat rate |
| Active sulfur | 12–18% | 18–25% | Drives EP response and copper attack |
| Kinematic viscosity at 100 °C | 20–60 mm²/s | 60–120 mm²/s | Affects blending and pumpability |
| Chlorine | ≤ 0.3% | ≤ 0.5% | Regulatory and seal compatibility |
| Appearance | Amber to dark brown viscous liquid | Dark brown, heavier body | Visual check only, not a spec |
Viscosity is the parameter buyers most often overlook. A high-viscosity grade is harder to blend into a light gear oil and can haze if the addition temperature is too low. Ask which band routine production sits in, not just what the range allows.
Reading the Certificate of Analysis
A useful CoA for T321 carries the lot number, production date, total sulfur, active sulfur, chlorine, viscosity at 100 °C, flash point, density and appearance. Anything less is a shipping document, not a quality document.
Three checks belong in incoming inspection. Iodometric or gravimetric sulfur determination confirms the headline number. The copper strip corrosion test shows whether active sulfur sits in the expected band. A four-ball EP test — weld load or last non-seizure load — ties chemistry to performance. Retain a sealed sample from every lot; when a gear oil fails an FZG retest six months later, that sample turns an argument into evidence.
Copper Strip Corrosion and Seal Compatibility
Active sulfur is indiscriminate. It will form a sulfide film on bronze synchroniser rings and copper cooler tubing just as readily as on a steel gear flank. Formulators manage this with copper deactivators and corrosion inhibitor packages, but the starting point is knowing the active sulfur level you are buying. For transmissions with yellow-metal components, specify the lower end of the active sulfur band and confirm the copper strip result at 100 °C for three hours. For industrial gear oils on steel-only gearing, the higher band buys treat-rate efficiency with little downside.
Seal compatibility runs the other way: highly sulfurized products can swell or harden nitrile and polyacrylate seals over time. If the end application carries an OEM seal specification, test the finished lubricant rather than the additive alone.
Handling, Packaging and Shelf Life
T321 is supplied in 200 litre drums, 1000 litre IBCs, and ISO tanks. It is viscous, so drums should be stored indoors and warmed to 40 to 60 °C before pumping; cold product will not drain cleanly and leaves a heel. Shelf life runs twelve to twenty-four months in closed containers, and slow reaction with dissolved oxygen shifts the active-to-total sulfur ratio. Request nitrogen blanketing for stock held over a season.
How to Qualify a Supplier
Four things separate a reliable supplier from a trader.
Batch consistency. Ask for the last six CoAs for the same grade and compare the sulfur and viscosity spread. Total sulfur that varies by eight points between lots costs you in reformulation and retesting.
Manufacturing route. Direct sulfurization of isobutylene oligomer behaves differently from a chloride-assisted route; the chlorine number tells you which you are getting.
Named test methods. A supplier who can state the ASTM or GB method behind each CoA line has a functioning laboratory. One who cannot is relaying someone else’s numbers.
Documentation. MSDS in the destination language, UN-compliant marking, and a shipping document matching the CoA lot number.
For the underlying chemistry — how the sulfur bridges form and where the product sits against other EP chemistries — the site’s explainer on what sulfurized isobutylene is covers the structure, and the guide to extreme pressure additives for lubricants sets out how sulfur, phosphorus and chlorine chemistries compare on load stage and temperature range.
FAQ
Is T321 the same as sulfurized isobutylene? T321 is the common designation for the standard grade, used interchangeably in trade. The specification behind it is not standardised, so always buy against a written spec.
Can T321 replace a sulfur-phosphorus package? Only partially. Sulfurized isobutylene carries the load, but phosphorus supplies antiwear and friction control that sulfur alone does not. Most gear oil packages combine both.
What sulfur level should I specify? Specify the application, not the number: the gear type, the load stage you must pass, and whether yellow metals are present — then ask the supplier to propose the grade with test data.
Conclusion
Sulfurized isobutylene looks like a commodity and behaves like a specification-driven product. Buyers who get consistent performance write total sulfur, active sulfur, chlorine and viscosity into the purchase specification, test each lot rather than trusting the certificate, and hold retained samples against future disputes. Everything else is a price conversation that eventually becomes a quality problem.

