Sodium diethyl dithiocarbamate — known across Chinese mineral processing as ethyl thiocarbamate, DDTC, or by the grade designation T-114 — is the collector a lead-zinc concentrator reaches for when a xanthate-only scheme will not hold galena grade. Its value is not raw collecting power. It is the ability to float lead minerals hard while barely touching pyrite and unactivated sphalerite, which is exactly the differential a lead rougher needs.
Quick answer: sodium diethyl dithiocarbamate is a water-soluble dithiocarbamate collector, formula (C2H5)2NCSSNa, typically supplied at 90 percent or higher active content, dosed in the tens of grams per tonne and blended with xanthates to balance recovery against selectivity. It is used mainly in lead-zinc and copper-lead flotation, where it outperforms xanthates on galena grade.
Why the Chemistry Gives Selectivity
DDTC shares the sulphur-bearing collecting group of the xanthates but hangs it on a nitrogen base instead of an oxygen linkage. That structural change shifts how the molecule adsorbs: it bonds readily to lead and copper sulphide surfaces and much more weakly to iron sulphide.
In a classic lead-zinc flowsheet, the sequence is lead rougher, lead cleaners, then activation and flotation of sphalerite. For that sequence to work, sphalerite and pyrite must stay depressed during the lead stage. DDTC supports this in two ways. As the lead-stage collector it floats galena strongly while leaving unactivated sphalerite largely uncollected. And because the reagent is run alongside the standard depressant suite — zinc sulfate plus lime, with cyanide where regulations still permit it — pyrite is held back by pH while galena reports to the froth.
The result is a higher-grade lead concentrate with fewer cleaning stages to reject iron sulphides. In copper-lead bulk circuits, the same selectivity floats copper and lead away from pyrite before separation. For the depressant side of that balance, the guide to zinc sulfate flotation depressant sets out how the zinc sulphate and lime regime is controlled.
How It Is Used in Practice
DDTC is rarely the only collector in the circuit. Standard practice blends it with xanthates:
- A small DDTC addition lifts galena recovery where xanthate alone leaves slow-floating coarse or partly oxidised galena behind.
- Blending with sodium butyl or ethyl xanthate keeps froth load up while the dithiocarbamate supplies selectivity the xanthate lacks.
- Because dithiocarbamates are weak frothers, the scheme still needs MIBC or a suitable alcohol frother to build stable froth.
Total collector dosage usually sits in the tens of grams per tonne, with the DDTC share set by locked-cycle tests on the plant’s own ore. Over-dosing erodes the selectivity that justifies the price premium, so blend ratio deserves the change-control discipline applied to pH.
One habit matters more than most: prepare DDTC as a fresh solution on the day of use. Like most sulphur collectors it oxidises slowly in solution, and a stale solution loses collecting power in a way that looks like an ore change rather than a reagent problem.

Specification: What to Write Into a Purchase Order
Commercial DDTC is sold on active content, and that is the number that should drive both price comparison and dosage calculation. Gross weight means little if the assay is 85 percent instead of 95 percent.
| Parameter | Typical commercial specification | Why it matters |
|—|—|—|
| Active content (assay) | ≥ 90%, high grades ≥ 95% | Directly scales the effective dose per tonne |
| Appearance | White to pale crystalline solid | Discoloration suggests oxidation or contamination |
| Moisture | Low, sealed packaging | Hydrolysis and caking in storage |
| Water insolubles | Very low | Residue fouls dosing lines and filters |
| pH of solution | Alkaline | Indicates residual alkali and stability |
| Bulk density / particle size | Grade-dependent | Dissolving time and dust generation |
Three points cause most disputes. Assay basis: confirm whether the certificate reports sodium diethyl dithiocarbamate content or a trihydrate-equivalent figure, because the two are not interchangeable. Solubility: product that leaves residue in the dissolving tank blinds dosing lines over weeks. And batch consistency — selectivity depends on consistent chemistry delivery after delivery, so a certificate per lot is not a formality.
Buyers comparing quotations should normalise to cost per kilogram of active content, then add freight and packaging to reach a landed figure. A cheaper drum at lower assay frequently loses on that basis.
Packaging, Storage and Shelf Life
DDTC is moisture-sensitive. It ships in sealed, waterproof inner-lined drums or woven bags with a laminated barrier, and it should be stored dry, cool and out of direct sunlight. Once a package is opened, the remainder should be resealed and used promptly; caked product dissolves poorly and doses inaccurately.
Under dry storage, shelf life is measured in months rather than years. Stock rotation matters more than the printed date, because the degradation that hurts performance — slow oxidation — begins the moment moisture and air reach the product. In humid climates, desiccant sachets in the drum and a sealed dosing hopper are cheap insurance.
Handling is straightforward but not casual: use dust protection when charging dry product, avoid contact with acids and oxidising agents, and sweep spills dry rather than washing them into drains — the solution is a significant COD load for any effluent plant.
Supplier Qualification
Four questions separate a manufacturer from a trader with a warehouse:
Consistent assay across lots. Ask for the last six certificates for the same grade and compare the spread. A range of ten points between lots will show up as concentrate grade drift.
Named analytical method. A supplier who can state the method behind the assay number has a working laboratory. One who cannot is relaying someone else’s paperwork.
Declared moisture and insolubles limits. These two parameters predict how the product behaves in a dissolving tank far better than appearance does.
Documentation and packaging discipline. A current safety data sheet in the destination language, UN-compliant marking where applicable, and shipping documents that match the certificate lot number.
For the collector families that DDTC is blended with, the xanthate selection guide for copper and lead-zinc ores compares the xanthate options on selectivity and cost, and the complete guide to flotation reagents places collectors, frothers and regulators in one scheme.
FAQ
Is DDTC the same as ethyl xanthate? No. Both are sulphydryl collectors, but xanthates are built on an oxygen linkage and dithiocarbamates on a nitrogen base. DDTC is considerably more selective for galena over pyrite, and considerably more expensive per tonne.
What dosage is typical? Tens of grams per tonne, usually blended with xanthate. Confirm the DDTC share by locked-cycle testing on the actual ore rather than copying another plant.
Can DDTC replace xanthate entirely? Rarely economic. It is normally used as a selectivity booster alongside xanthate, not as a full substitution.
Conclusion
Sodium diethyl dithiocarbamate earns its premium in circuits where lead grade, not lead recovery, is the constraint. Buying it well comes down to three habits: specify active content and moisture rather than accepting a headline purity figure, compare quotations on cost per kilogram of active content landed, and demand lot certificates against a retained sample. The chemistry is well understood; the commercial execution is where circuits quietly lose money.

