news

Copper Sulfate Flotation Activator: Sphalerite Activation and Dose Control

Copper sulfate is the activator most lead-zinc concentrators add when sphalerite refuses to float. It is cheap per kilogram, easy to dissolve, and responsible for a disproportionate share of grade losses when it is dosed by habit rather than by measurement. This guide covers what copper sulfate actually does at the mineral surface, how dose and pH interact, and what to write into a purchase specification.

Quick answer: copper sulfate pentahydrate (CuSO₄·5H₂O) activates sphalerite by exchanging Cu²⁺ onto the mineral surface, creating a copper-sulfide-like layer that xanthate can collect. Typical addition is 100 to 500 g/t, staged into the grind and conditioner rather than dumped at one point. It also activates pyrite and pyrrhotite, so selectivity depends on lime control and on keeping the dose at the minimum that delivers recovery.

What Activation Actually Means

Sphalerite is zinc sulfide, and xanthate does not adsorb on it well. Copper sulfate changes that. Copper ions in solution exchange with zinc at the surface, leaving a copper-rich sulfide film that behaves, to a collector, much like a copper mineral. Once that film exists, xanthate chemisorbs and the particle becomes floatable.

Three practical consequences follow.

The reaction is surface-limited, so it depends on liberation and on contact time in the conditioner. Fine, well-liberated sphalerite activates quickly; coarse or locked particles need longer conditioning and may never activate fully.

The reaction consumes copper, so dose is not a fixed number. It scales with the surface area of sphalerite present, which changes with ore blend and grind size.

And it is not selective. Copper ions will activate pyrite, pyrrhotite and other iron sulfides equally well, which is why the same reagent that lifts zinc recovery can wreck lead concentrate grade.

Dose, Staging and pH

Dose is normally quoted as grams per tonne of feed, with 100 to 500 g/t covering most lead-zinc circuits. The number matters less than where it goes.

Stage the addition. Adding copper sulfate in the grinding mill gives maximum contact time and the most complete activation, but it also activates everything, including pyrite that will report to the lead circuit. Adding it in the conditioner before zinc roughers is more selective but needs enough residence time — typically several minutes — to complete the surface exchange.

Control pH deliberately. Activation is favoured at moderate alkalinity. Very high lime addition, used to depress pyrite, also suppresses sphalerite activation; plants often trade lead grade against zinc recovery by moving lime setpoints. The right operating point is circuit-specific and should be established by locked-cycle testing, not copied from another concentrator.

Watch the copper balance. In circuits with chalcocite or other secondary copper minerals, soluble copper in the process water may already be activating sphalerite. Adding copper sulfate on top of that produces over-activation, slimy froths and zinc reporting into the lead concentrate.

Preparation and Dosing Practicalities

Copper sulfate pentahydrate dissolves readily in water, and most plants prepare a 10 to 20 percent stock solution. Two details matter.

Dissolve in a dedicated tank with agitation and add the solid to water, not water to solid. Copper sulfate is acidic in solution and corrosive to mild steel at strength, so dosing lines, pumps and tanks should be plastic, rubber-lined or stainless.

Solution temperature affects solubility substantially; a stock solution prepared cold on a winter morning will be weaker than the same recipe in summer, which is one reason dose records and assay records must be kept together.

Blue copper sulfate pentahydrate crystals dissolving in a plastic-lined mixing tank

Specification: What to Buy

| Parameter | Typical specification | Why it matters |

|—|—|—|

| CuSO₄·5H₂O content | 96% minimum | Directly sets active copper per tonne |

| Copper (Cu) content | 24.5% minimum | Basis for dose calculation |

| Iron (Fe) | 0.1% maximum | Impurity load in the circuit |

| Water-insoluble matter | 0.05% maximum | Sediment and dosing-line blockage |

| pH (5% solution) | 3.0–4.5 | Indicator of acidity and handling needs |

| Appearance | Blue crystals, free-flowing | Caking indicates moisture uptake |

Buyers should confirm whether the certificate reports pentahydrate content or copper content — the two differ by roughly a factor of four, and quotations are not comparable until they are normalized.

Anhydrous copper sulfate exists and carries more copper per tonne, but it is hygroscopic and less common in flotation supply. If a supplier offers “copper sulfate” without naming the hydrate form, ask.

Storage, Handling and Safety

Copper sulfate pentahydrate is stable in dry storage but takes up moisture and cakes if drums are left open. Store under cover on pallets, keep bags sealed, and rotate stock.

It is a hazardous material in the environmental sense rather than the acute-toxicity sense: it is harmful to aquatic life and must not reach drains or tailings discharge untreated. Dust irritates eyes and respiratory tract, so bag handling needs dust control. Spills should be swept dry, not washed down.

For the interaction between copper sulfate and the depressant side of a copper-molybdenum separation, the site’s guide to copper sulfate and sodium hydrosulfide in flotation covers how the two reagents are sequenced, and the broader flotation reagents guide sets out where activators sit in a reagent scheme.

FAQ

How much copper sulfate should I add? Most lead-zinc circuits run 100 to 500 g/t, staged into grind or conditioner. Confirm the figure by locked-cycle testing on the actual ore blend; the correct dose changes when the sphalerite content or grind size changes.

Why did zinc recovery drop after we cut copper sulfate? Because activation is surface-area dependent. A dose that worked at a coarse grind may be insufficient after a finer grind, or with a higher-sphalerite ore blend. Re-test rather than restoring the old number.

Can copper sulfate replace a zinc sulfate depressant? No. They do opposite jobs: copper sulfate activates sphalerite for zinc flotation, while zinc sulfate depresses sphalerite during lead flotation. Running both in the same circuit is normal; they are added at different stages.

Conclusion

Copper sulfate is the cheapest lever in a lead-zinc circuit and the easiest to misuse. Specify the hydrate form and copper content, dissolve and dose it in the right place, keep lime setpoints under control, and re-establish the dose whenever ore blend or grind changes. Circuits that treat activation as a measured unit operation get both zinc recovery and lead grade; circuits that treat it as a fixed recipe get one at the expense of the other.

Leave a Reply